.". Workplace Safety And Health ,WSH Safety Resources Blog: August 2024

Featured Post

MOM Revised Heat Stress Framework

REVISED FRAMEWORK TO GUIDE EMPLOYERS AND PROTECT OUTDOOR WORKERS AGAINST HEAT STRESS With global warming, rising temperatures in Singapore w...

Saturday, August 31, 2024

Construction Site Workplace Fatality

SINGAPORE: A 35-year-old construction worker died  after he was struck by a reversing dump truck at a worksite at a junction of Tanah Merah Coast Road and the Changi East development, said the Ministry of Manpower (MOM) on Friday

A 36-year-old man was arrested for causing death by a rash or negligent act, said the police, adding that investigations are ongoing.

The construction worker was employed by Hua Hao Development, while the occupier of the worksite is Huationg Contractor, said an MOM spokesperson in response to queries from CNA on Friday.

"As a general safety measure, a traffic management plan must be implemented to ensure the safe movement of vehicles and pedestrians in the workplace, including the deployment of a trained banksman to guide reversing vehicles when necessary," said the spokesperson.

The spokesperson added that MOM is also investigating the incident.

Learning points to consider: 

1. *Clear visibility and spotters*: 

Ensure that drivers of reversing vehicles have clear visibility or are assisted by spotters to prevent accidents. This can be achieved through proper training, use of cameras or sensors, and designated spotters. 

2. *Segregation of pedestrians and vehicles*: 

Implement effective segregation measures to separate pedestrians and vehicles, reducing the risk of accidents. This can include designated walkways, barriers, and clear signage. 

3. *Reversing protocols and procedures*: 

Establish and enforce strict reversing protocols and procedures, including: - Mandatory spotters or guides - Use of reverse alarms or warning lights - Designated reversing areas or zones - Worker training on reversing hazards and procedures

Vehicular Safety in Workplaces

Four workplace fatalities and 19 major injuries1 resulting from vehicular-related accidents (excluding work-related traffic accidents)reported in 2023. Root cause identified include; Lack of a or inadequate Traffic Management Plan (TMP), non-compliance to the TMP, and negligence by the vehicle operator and/or co-workers are common causes of vehicular-related incidents in the workplace.

The Ministry of Manpower (MOM) will be conducting inspections targeting vehicular safety in industries such as transport & storage, marine, manufacturing, services, and construction in the upcoming months, 

Below are good workplace safety and health (WSH) practices commonly adopted by companies to prevent vehicular-related incidents. The WSH Council urges companies to establish a TMP and adopt these good practices to be well prepared for MOM’s upcoming inspections














Saturday, August 3, 2024

WSH Circular WSH Coordinator Training

WSH Circular WSH Coordinator Refresher Training

To: Construction Companies that employ WSH Coordinators

WSH Coordinator Refresher Training

With reference to the circular MOM/OSHD/2023-02 issued on 16 Feb 2023 (refer to https://www.mom.gov.sg/workplace-safety-and-health/wsh-circulars), the Ministry of Manpower (MOM) reminds Construction Companies to send WSH Coordinators who are appointed to work in their worksites to attend the WSH Coordinator Refresher Training every two years.

2 The WSH Act requires the Employer and the Principal to take reasonably practicable measures to ensure the safety and health of the workers. This includes providing these workers with adequate training for them to perform their work. The WSH Coordinator Refresher Training provides continuous training to build up

a WSH Coordinator’s competencies in assisting the occupier to manage workplace injury risks. This allows the WSH Coordinator to bridge WSH directives from the management to workers, and see to the implementation and compliance with WSH practices.

4. The refresher training will be conducted in two parts:

i) e-learning (to be completed within a week), which can be carried out anywhere, anytime, and completed by different sections, at the participant’s convenience using his/her mobile phones or any other internet-connected devices; AND

ii) a one day in-person training session, AFTER the participant has completed his/her e-learning.

5. The refresher training provides new information not covered in the WSH Coordinators’ Advanced Certificate in WSH course. Learners will be updated on the latest WSH developments, and key areas such as good WSH practices and effective management of contractors. There will be activities where they can apply their knowledge and skills to practical work scenarios with case studies relevant to construction as well as other different industries.

6. The refresher training fees is estimated to be about $100, at the company’s cost, and should not be deducted from the WSH Coordinator’s salary. You may contact either training provider, as listed below, to sign up your WSH Coordinator/s for the refresher training and register via the registration QR code. The training provider will assist with the setting up of email address account, if required, for any WSH Coordinator who does not have an email address account. The email address is necessary and required for the WSH Coordinator to access the e-learning.


7. To access the FAQs on the programme, you may scan the QR code below:


8. All WSH Coordinators who attend the refresher training will have their training records updated in MOM WSH Training Record System (TRS). MOM may conduct checks to ensure compliance of the training requirement for all your WSH Coordinators.

9. For any query pertaining to the WSH Coordinator Refresher Training, please email to wsh_training@wshc.sg.




WSH Circular Safe Use Storage Racks

 WSH Circular Safe Use of Storage Racks


FACTORIES WITH WAREHOUSE STORAGE

Occupiers and employers engaged in warehouse and storage operations are reminded to take all reasonably practicable measures to ensure that the storage racks at your workplace are safe for use. You may refer to Annex A for guidance on some of the relevant WSH requirements. 

Step 1. Check your existing storage racks to ensure that they are designed for the intended storage load and have been properly installed.

Step 2. Perform a risk assessment on the use of storage racks.

Step 3. Establish a maintenance regime for the storage racks.

Annex A - Relevant WSH Requirements for Safe Use of Storage Racks

The following is a non-comprehensive list of relevant WSH requirements.

1) Design Consideration

The design of storage racks must allow for safe use and maintenance. The following should be considered in the design of storage racks:

a) Storage racks must be structurally stable and designed with the intended use in mind (e.g. weight, volume, shape, dimensions, environment to be used in etc.).

b) The safe working load of the storage racks should be prominently displayed. In particular, if the storage racks are stacked, the lower racks must be designed to take into account of the weight of the upper racks and their corresponding goods.

c) There should be safe means of access to the goods being stored, including proper work-at-heights measures.

d) The physical environment where the storage racks are to be used should be considered. For example, racks that are placed in areas where there is vehicular moment (e.g. forklifts, reach trucks etc) should be designed to withstand impact from possible collisions. In a cold room environment, temperature swings may require special considerations for corrosion protection due to moisture and other effects on the structural integrity of storage racks.

e) A re-assessment of the storage rack’s design should be carried before any change of use, including a change in the nature of goods to be stored.

2) Use of Storage Racks

The following measures are to be taken when using storage racks:

a) Use of storage racks should be carried out in accordance with the manufacturer’s instructions.

b) Conduct a risk assessment for the use of the storage racks.

c) Establish safe work procedures for work activities involving storage racks. The procedures should include confirming that the combined weight of the intended goods to be stored does not exceed the safe working load of the racks. In particular, if the racks are stacked, the bottom racks must have sufficient loading capacity to hold the racks and goods stored above.

d) Ensure that warehouse personnel made aware of the safe working loads and are trained on the safe work procedures for stacking and/or storage of goods.

3) Maintenance of Storage Racks

The following measures are to be taken when maintaining storage racks:

a) Maintenance of the storage racks should be carried out in accordance with the manufacturer’s instruction.

b) Storage racks and accompanying accessories (including pallets) should be regularly inspected to ensure their structural integrity (for example, no signs of damage or corrosion). Any defective part must be repaired or replaced before use.

Joint Circular on Nail Salon Safety

 Protecting Employees’ and Customers’ Health from Chemicals in Nail Salons


This circular provides guidance to nail salons on measures that can protect employees’ and customers’ health by minimising exposure to harmful chemicals.


Nail care products such as nail polishes, fingernail glues, and nail polish removers contain chemicals, some of which can be harmful to the health of nail salon employees and customers1. These products are regulated as cosmetic products under the Health Products

Act and must meet safety requirements specified in Act, as well as the Health Products (Cosmetic Products – ASEAN Cosmetic Directive) Regulations. To assist nail salons with

compliance, the safety requirements are set out in this Circular.


Use products that comply with safety requirements


a. Check that nail care products have been notified with the Health Sciences Authority (HSA), by checking HSA’s infosearch. Ensure that nail care products used do not contain prohibited chemicals and that restricted chemicals are used within the specified conditions

of use by referring to the Third Schedule of the cosmetic products regulation. For example:

▪ Formaldehyde is not allowed to be added as an ingredient into all cosmetic products, including nail care products.

▪ Toluene is only permitted in nail care products up to a maximum

concentration of 25%.

o A cosmetic product containing prohibited chemicals or using restricted chemicals not within the specified conditions of use would be considered an unwholesome health product. A person who manufactures, imports, or supplies an unwholesome

A person who manufactures, imports, or supplies an unwholesome health product is liable to a fine of up to $50,000 and/or imprisonment up to 2 years.


If the product cannot be found on HSA’s infosearch, inform your nail care product supplier to submit a notification via HSA’s website. A person who supplies an un-notified cosmetic product is liable to a fine of up to $20,000 and/or imprisonment up to 12 months.


b. Ensure that nail care products used comply with labelling requirements, including listing all ingredients on the product labels.

o Inform your nail care product supplier to add a warning label of “Contains formaldehyde”, if their products contain permitted preservatives that can release formaldehyde2 exceeding 0.05%.

o A person who supplies a cosmetic product that does not comply with this labelling requirement is liable to a fine of up to $50,000 and/or imprisonment up to 2 years.


Choose safer products

c. Minimise chemical exposures by using products that are water-based or have a low content of volatile organic compounds (VOCs, such as formaldehyde, toluene, xylene).


Follow safe work practices

d. Communicate to employees the hazards of handling nail care products, and encourage them to adopt safe work practices such as:

o Good housekeeping, e.g. keep dispenser bottles closed when not in use, clean up spills immediately.

o When applying nail care products, use only the amount needed to minimise chemical emissions into the air.

o Dispose of waste containing nail care products in sealed bags or keep wastebins covered. Empty wastebins frequently.

o Where needed, use personal protective equipment (PPE) such as gloves and goggles to protect employees’ skin and eyes. Nail salon operators should refer to the information in product labels or information sheets and provide the appropriate PPEs where necessary.


Ensure good ventilation and indoor air quality


e. Ventilate the space within the nail salon. If the salon has an air-conditioning and mechanical ventilation system that provides

outdoor air, check that the system is in good working condition.

o In air-conditioned spaces with no outdoor air supply, consider opening doors and windows to facilitate air exchange when feasible. Additionally, consider using local exhaust systems such as portable ventilation machines or ventilated tables to minimise exposure to VOCs emitted.


f. To maintain good indoor air quality for the wellbeing of customers and employees, operators may also refer to the advisory limits of specific VOCs in the Singapore Standard SS554: Code Of Practice For Indoor Air Quality For Air-Conditioned Buildings.




Useful resources

1. Stay Healthy and Safe While Giving Manicures and Pedicures – a Guide for Nail Salon Workers, U.S. Department of Labor, Occupational Safety and Health Administration, 2012, https://www.osha.gov/Publications/3542nail-salon-workers-guide.pdf

2. Controlling Chemical Hazards During the Application of Artificial Fingernails, U.S. Department of Health and Human Services, National Institute for Occupational Safety and Health, 1999, https://www.cdc.gov/niosh/docs/99-112/default.html

3. Information Sheet: Taking care of your chemical health and safety in nail bars and salons, Health and Safety Authority, Ireland.

https://www.hsa.ie/eng/Publications_and_Forms/Publications/Chemical_and_ Hazardous_Substances/Nail_Bars_Info_Sheet.pdf


Note 1 Exposure to chemicals in nail care products may occur via three routes: (1) inhaling volatile organic compounds

(VOCs such as formaldehyde, toluene, xylene) emitted from the products; (2) getting the products on skin or in eyes; or (3) ingesting the products that have come in contact with food or drinks. For example, exposure to formaldehyde can be through inhalation and this may lead to respiratory irritations, allergic reactions, and even

long-term serious health effects such as cancer


SCDF upcoming events

(adsbygoogle = window.adsbygoogle || []).push({});

Upcoming Events

HardwareZone Singapore

Jobs Portal