Confined Space Entry Safety Checklist

Safety Checklist For Working In Confined Space

SAFETY CHECKLIST FOR WORKING IN A CONFINED SPACE ENVIRONMENT
Safety Questionnaire		WSH ( Confined Space) Regulations	Yes	No
	Are all lines to a confined space, containing inert, toxic, flammable, or corrosive materials valved off and blanked or disconnected and separated before entry?
	Are all impellers, agitators, or other moving parts and equipment inside confined spaces locked-out if they present a hazard?
	Is either natural or mechanical ventilation provided prior to confined space entry?
	Are appropriate atmospheric tests performed to check for oxygen deficiency, toxic substances and explosive concentrations in the confined space before entry?
	Is adequate illumination provided for the work to be performed in the confined space?
	Is the atmosphere inside the confined space frequently tested or continuously monitored during conduct of work? Is there an assigned safety standby employee outside of the confined space? When required, whose sole responsibility is to watch the work in progress, sound an alarm if necessary, and render assistance
	Is the standby employee appropriately trained and equipped to handle an emergency?
	Is the standby employee or other employees prohibited from entering the confined space without lifelines and respiratory equipment if there is any question as to the cause of an emergency?
	Is approved respiratory equipment required if the atmosphere inside the confined space cannot be made acceptable
	Is all portable electrical equipment used inside confined spaces either grounded and insulated, or equipped with ground fault protection?
	Before gas welding or burning is started in a confined space, are hoses checked for leaks, compressed gas bottles forbidden inside of the confined space, torches lighted only outside of the confined area and the confined area tested for an explosive atmosphere each time before a lighted torch is to be taken into the confined space?
	If employees will be using oxygen-consuming equipment-such as salamanders, torches, and furnaces, in a confined space-is sufficient air provided to assure combustion without reducing the oxygen concentration of the atmosphere below 19.5 percent by volume?
	Whenever combustion-type equipment is used in a confined space, are provisions made to ensure the exhaust gases are vented outside of the enclosure?
	Is each confined space checked for decaying vegetation or animal matter which may produce methane?
	Is the confined space checked for possible industrial waste which could contain toxic properties?
	If the confined space is below the ground and near areas where motor vehicles will be operating, is it possible for vehicle exhaust or carbon monoxide to enter the space?
	Is there a team of trained personnel for confined space rescue work?
	Are all impellers, agitators, or other moving parts and equipment inside confined spaces locked-out if they present a hazard?
	Is either natural or mechanical ventilation provided prior to confined space entry?
	Are appropriate atmospheric tests performed to check for oxygen deficiency, toxic substances and explosive concentrations in the confined space before entry?
	Is adequate illumination provided for the work to be performed in the confined space?
	Is the atmosphere inside the confined space frequently tested or continuously monitored during conduct of work? Is there an assigned safety standby employee outside of the confined space? When required, whose sole responsibility is to watch the work in progress, sound an alarm if necessary, and render assistance
	Is the standby employee appropriately trained and equipped to handle an emergency?
	Is the standby employee or other employees prohibited from entering the confined space without lifelines and respiratory equipment if there is any question as to the cause of an emergency?
	Is approved respiratory equipment required if the atmosphere inside the confined space cannot be made acceptable
	Is all portable electrical equipment used inside confined spaces either grounded and insulated, or equipped with ground fault protection?
	Before gas welding or burning is started in a confined space, are hoses checked for leaks, compressed gas bottles forbidden inside of the confined space, torches lighted only outside of the confined area and the confined area tested for an explosive atmosphere each time before a lighted torch is to be taken into the confined space?
	If employees will be using oxygen-consuming equipment-such as salamanders, torches, and furnaces, in a confined space-is sufficient air provided to assure combustion without reducing the oxygen concentration of the atmosphere below 19.5 percent by volume?
	Whenever combustion-type equipment is used in a confined space, are provisions made to ensure the exhaust gases are vented outside of the enclosure?
	Is each confined space checked for decaying vegetation or animal matter which may produce methane?
	Is the confined space checked for possible industrial waste which could contain toxic properties?
	If the confined space is below the ground and near areas where motor vehicles will be operating, is it possible for vehicle exhaust or carbon monoxide to enter the space?

• 
  
  

Electrical Work Safety Checklist

Safety Checklist For Electrical Work

SAFETY CHECKLIST FOR ELECTRICAL
Safety Questionnaire			Yes	No
	Do you specify compliance with OSHA for all contract electrical work?
	Are all employees required to report as soon as practicable any obvious hazard to life or property observed in connection with electrical equipment or lines?
	Are employees instructed to make preliminary inspections and/or appropriate tests to determine what conditions exist before starting work on electrical equipment or lines?
	When electrical equipment or lines are to be serviced, maintained or adjusted, are necessary switches opened, locked-out and tagged whenever possible
	Are portable electrical tools and equipment grounded or of the double insulated type?
	Are electrical appliances such as vacuum cleaners, polishers, and vending machines grounded
	Do extension cords being used have a grounding conductor?
	Are multiple plug adaptors prohibited?
	Are ground-fault circuit interrupters installed on each temporary 15 or 20 ampere, 120 volt AC circuit at locations where construction, demolition, modifications, alterations or excavations are being performed?
	Are all temporary circuits protected by suitable disconnecting switches or plug connectors at the junction with permanent wiring?
	Do you have electrical installations in hazardous dust or vapor areas? If so, do they meet the National Electrical Code (NEC) for hazardous locations?
	Is exposed wiring and cords with frayed or deteriorated insulation repaired or replaced promptly?
	Are flexible cords and cables free of splices or taps?
	Are clamps or other securing means provided on flexible cords or cables at plugs, receptacles, tools, equipment, etc., and is the cord jacket securely held in place? Are all cord, cable and raceway connections intact and secure?
	In wet or damp locations, are electrical tools and equipment appropriate for the use or location or otherwise protected?
	Is the location of electrical power lines and cables (overhead, underground, under floor, other side of walls) determined before digging, drilling or similar work is begun?
	Is the use of metal ladders prohibited in areas where the ladder or the person using the ladder could come in contact with energized parts of equipment, fixtures or circuit conductors?
	Are all disconnecting switches and circuit breakers labeled to indicate their use or equipment served?
	Are disconnecting means always opened before fuses are replaced?
	Do all interior wiring systems include provisions for grounding metal parts of electrical raceways, equipment and enclosures?
	Are all electrical raceways and enclosures securely fastened in place?
	Are all energized parts of electrical circuits and equipment guarded against accidental contact by approved cabinets or enclosures?
	Is sufficient access and working space provided and maintained about all electrical equipment to permit ready and safe operations and maintenance?
	Are all unused openings (including conduit knockouts) in electrical enclosures and fittings closed with appropriate covers, plugs or plates?
	Are disconnecting switches for electrical motors in excess of two horsepower, capable of opening the circuit when the motor is in a stalled condition, without exploding? (Switches must be horsepower rated equal to or in excess of the motor hp rating.) Is low voltage protection provided in the control device of motors driving machines or equipment which could cause probable injury from inadvertent starting?
	Is each motor disconnecting switch or circuit breaker located within sight of the motor control device? Is each motor located within
	Is each motor located within sight of its controller or the controller disconnecting means capable of being locked in the open position or is a separate disconnecting means installed in the circuit within sight of the motor?
	Is the controller for each motor in excess of two horsepower, rated in horsepower equal to or in excess of the rating of the motor it serves?
	Are employees who regularly work on or around energized electrical equipment or lines instructed in the cardiopulmonary resuscitation (CPR) methods?
	Are employees prohibited from working alone on energized lines or equipment over 600 volts?